Products

NIPS hollow fiber membrane spinning is a process for preparing hollow fiber membranes via non-solvent induced phase separation (NIPS). The core principle is to extrude a polymer dope through a spinneret into a non-solvent coagulation bath, where solvent/non-solvent exchange drives polymer phase separation and solidification, forming a hollow structure with an asymmetric porous morphology. This process is widely used in water treatment, gas separation, and medical applications.
A NIPS hollow fiber membrane spinning equipment mainly includes four core sections: dope preparation, metering and extrusion, coagulation and forming, and post treatment and take up system. The hollow fiber emmbrane spinning machine performance and stability determine the quality and properties of the hollow fiber membrane. Leveraging 11 years of experience and R&D, Trustech has upgraded the SteadyiCore Ultra 2.0 Heating System, TitanMix Pro 4.0 Mixing System, PrimeGlider Pro 3.0 Automatic Pay-off, SmartCoil Elit

A braided-reinforced hollow fiber spinning line typically comprises five coordinated sections: dope preparation, metering and co-extrusion, braid handling and synchronization, coagulation and structural fixing, and post-treatment and take-up. Compared with conventional NIPS lines, the braided pathway adds two critical engineering challenges—precise tension control and concentric alignment—to ensure uniform coating thickness, consistent porosity, and strong interfacial bonding between the polymer sheath and the braid.

Leveraging over 12 years of engineering and R&D, modern systems integrate closed-loop thermal management for dope rheology, high-precision gear or servo metering pumps for stable mass flow, Trustech has upgraded the SteadyiCore Ultra 2.0 Heating System, TitanMix Pro 4.0 Mixing System, PrimeGlider Pro 3.0 Automatic Pay-off, SmartCoil Elite 3.0 Automatic Winding, and StoutDrive 2.0 motor drive setup.These technologies improve precision and stability.

NIPS hollow fiber membrane spinning is a process for preparing hollow fiber membranes via non-solvent induced phase separation (NIPS). The core principle is to extrude a polymer dope through a spinneret into a non-solvent coagulation bath, where solvent/non-solvent exchange drives polymer phase separation and solidification, forming a hollow structure with an asymmetric porous morphology. This process is widely used in water treatment, gas separation, and medical applications.
A NIPS hollow fiber membrane spinning equipment mainly includes four core sections: dope preparation, metering and extrusion, coagulation and forming, and post treatment and take up system. The hollow fiber emmbrane spinning machine performance and stability determine the quality and properties of the hollow fiber membrane. Leveraging 11 years of experience and R&D, Trustech has upgraded the SteadyiCore Ultra 2.0 Heating System, TitanMix Pro 4.0 Mixing System, PrimeGlider Pro 3.0 Automatic Pay-off, SmartCoil Elit

NIPS hollow fiber membrane spinning is a process for preparing hollow fiber membranes via non-solvent induced phase separation (NIPS). The core principle is to extrude a polymer dope through a spinneret into a non-solvent coagulation bath, where solvent/non-solvent exchange drives polymer phase separation and solidification, forming a hollow structure with an asymmetric porous morphology. This process is widely used in water treatment, gas separation, and medical applications.
A NIPS hollow fiber membrane spinning equipment mainly includes four core sections: dope preparation, metering and extrusion, coagulation and forming, and post treatment and take up system. The hollow fiber emmbrane spinning machine performance and stability determine the quality and properties of the hollow fiber membrane. Leveraging 11 years of experience and R&D, Trustech has upgraded the SteadyiCore Ultra 2.0 Heating System, TitanMix Pro 4.0 Mixing System, PrimeGlider Pro 3.0 Automatic Pay-off, SmartCoil Elit

Dual layer dope spinneret spinneret, also called a composite membrane spinneret, is a key forming component used in membrane separation/filtration manufacturing. In a single co-extrusion step, it laminates two or more functional dopes into a prescribed layered architecture and shapes them through micron-precision orifices or slots into a layer-by-layer structured membrane. Its core role is to stably and controllably stack and form multiple fluid streams within a microscale flow space.

A dry-jet wet spinning spinneret is the core forming component tailored to the Dry-Jet Wet Spinning process for producing hollow fiber membranes. THis spining spinneret primary function is to precisely co-extrude a polymer casting dope and a bore fluid through coaxial flow channels, so that the extruded "liquid filament" first passes through an air gap which calls dry zone for partial solvent evaporation and initial drawing, then enters a coagulation bath which calls wet zone for phase separation and solidification, ultimately forming hollow fibers membrane with specified structures and properties. The spinning spinneret must be designed to accommodate both "liquid filament stability in the air gap" and "initiation of phase separation in the coagulation bath,"acting as the critical bridge between dry state drawing and wet state solidification.

A sol - gel sintering spinning spinneret is a coaxial extrusion spinning assembly for inorganic/ ceramic hollow fiber membrane. The outer phase is a sol or organic–inorganic hybrid precursor, containing inorganic particles or precursor solution with organic binders/ porogens, while the inner phase is a supporting bore fluid which may be a coagulant, a nonsolvent, or an inert fluid. After shaping, the green fibers undergo gelation, solvent exchange, drying, debinding, and high temperature sintering, typically 400 - 1200°C, to yield dense or porous inorganic/ ceramic hollow fibers membrane such as alumina, zirconia, silica, titanates, and the approach is also applicable to metal/glass precursor systems.

Hollow fiber membrane spinnerets are the key parts for making hollow fiber membranes. The spinneret geometry, functional characteristics, and fabrication accuracy directly decide the fiber membrane's concentricity, wall uniformity, pore size distribution, mechanical robustness, and overall separation efficiency.

The FCT 6th generation spinneret plate is the core forming component for hollow fiber membranes, developed by Trustech based on Fast Change Technology (FCT) and designed specifically for wet-process NIPS (non-solvent induced phase separation) spinning.

A TIPS (Thermally Induced Phase Separation) membrane spinneret is the core component used for preparing polymer microporous membranes via the thermally induced phase separation method. Trusstech TIPS spinning spinneret is a hollow fiber spinning head specifically designed for the "high-temperature melt–cooling-induced porosity" route, used to produce microporous membranes from crystalline polymers such as PVDF, PP, and PE. Its structure and functions must simultaneously satisfy around-200°C melt sealing, rapid cooling induced pore formation, and controllable porosity. Its working principle relies on temperature changes to induce phase separation in a polymer solution, ultimately forming a membrane material with a microporous structure.

The rib-reinforced hollow fiber membrane spinneret, also called Core Fiber Reinforced Spinning Spinneret is a specialized spinneret assembly used for preparing hollow fiber membranes via non-solvent induced phase separation (NIPS). Based on conventional coaxial and multiphase spinneret structures, it adds a reinforcement filament introduction and positioning channel, which can stably introduce one or three high strength fine filaments (e.g., nylon/monofilament fishing line) into the membrane wall or at specific radial positions at the moment of fiber formation. The reinforcement filaments co-form with the membrane matrix in the coagulation bath, significantly improving tensile strength, anti-knotting, anti-brittle fracture performance, and resistance to operational stresses, without compromising the membrane's separation performance or hollow structure.

Trustech FCT 5th Generation Homogeneous Membrane Spinneret is the core forming equipment developed on the Fast Change Technology (FCT) . Featuring a “split spin core + flow channel plate” architecture and a high precision monolithic core,Trustech spinning spinneret is specifically designed for producing homogeneous polymer membranes such as gas separation membranes, pervaporation membranes, and high precision filtration membranes which exhibit uniform structure without a pronounced pore gradient. Building on the FCT series’ core strengths of “high precision and easy maintenance,” spinneret structure and features are specially optimized to meet the stringent requirements of homogeneous membranes for feed uniformity, structural stability, and performance consistency.